RepeatMasker & RepeatScout

[tnguyen]

Hi Rahul,

How large was your genome? How much memory was needed for your run? I received this error message at the start of Step 2:

"Could not allocate space for sequence"

[rahularjun86]

Dear All,
I ran Repeatscout successfully, Commands I used:

1225 ##RepeatSout Run
1226 #step1
1227 build_lmer_table -l 14 -sequence Final_assembly.fasta -freq Final_assembly.freq
1228 #step2
1229 RepeatScout -sequence Final_assembly.fasta -output Final_assembly_repeats.fasta -freq Final_assembly.freq -l 14
1230 #step3
1231 cat Final_assemblyf_repeats.fasta | filter-stage-1.prl > Final_assembly_repeats_filtered_stg1.fasta
1232 #step4
1233 RepeatMasker -pa 20 -s -lib Final_assembly_repeats_filtered_stg1.fasta Final_assembly.fasta &
1234 #step5
1235 cat Final_assembly_repeats_filtered_stg1.fasta | filter-stage-2.prl --cat=Final_assembly.fasta.out --thresh=3 > Final_assembly_repeats_filtered_stg2_thresh3.fasta
1236 #step6
1237 RepeatMasker -pa 20 -s -lib Final_assembly_repeats_filtered_stg2_thresh3.fasta Final_assembly.fasta &

[WhatsOEver]

Thats true and it works fine, but RepeatModeler also uses RepeatMasker and eventually the rmblast package, so you might have to face the same problems as described before.

[gprakhar]

Hello,

This is not a direct answer to your question, but there is a tool from the Repeat Masker group.
Its called Repeat Modeler, this tool integrates Repeat Scout, RECON and TRF.
It creates a de-novo repeat library and then annotates the sequences.
Repeat Modeler

--
pg

[WhatsOEver]

I don't know if its still an actual problem, but I had it too and was able to solve it on my system (ubuntu11, 64bit).
The libs RepeatMasker is looking for are not the downloaded ones, but the blast dbs that should have been created by rmblast. rmblast itself is looking for a libpcre.so.0 file which it could not find on my system. The file is known to cause problems with some progs as symlinks are not made correctly during updates.
Therefore I just created symlinks manually in my /lib/ and /lib32/ folder to the actual file (so just type "sudo ln -s /lib/libpcre.so.3 /lib/libpcre.so.0" and "sudo ln -s /lib32/libpcre.so.3 /lib32/libpcre.so.0") and afterwards everything worked fine for me

@edge: you don't need to change anything in the .prl file, but you need to rename the trf404-linux64 (or else) executable to simply to trf.

[sameoldmike]

same thing happened to me -- the filtered output file is empty after running for a very long time. it was run on a repeat-rich genome.

could it be that i don't have nseg and TRF properly installed? there is no output about those two programs that i can see...

[hkuntal]

repeatscout

hello everyone
i m try to work with repeatscout but every time when i m runninf filter-stage-1.prl, the filtered library generated is created empty( no data)..... any solution???

[edge]

Hi Zimbobo,

Can I ask you how you edit the perl script, filter-stage-1.prl to allow it point to the TRF path that we install?
Which line of filter-stage-1.prl that we need to edit the path of TRF?
My server keep on shown the below message:
"No such file or directory at ./filter-stage-1.prl line 110"
Thanks a lot for your sharing and guiding.

[Zimbobo]

I actually followed those instructions.

RepeatMasker is complaining still about missing libraries (ie Libraries/RepeatMasker.lib etc) and advises to get something from www.girinst.org.

The whole point of running RepeatScout for me is to build my own library. Is there a flag to teach RepeatMasker not to look for those libraries or is there a reason RepeatMasker must have those libraries?

[darked89]

Here is a recipe how to install and run RepeatScout:

http://openwetware.org/wiki/Wikiomics:Repeat_finding#RepeatScout

Hope it helps,

Darek

[Zimbobo]

Hello there,

I was wondering whether anybody on this list could knows how to run RepeatScout (1.0.5) and RepeatMasker (3.2.8).

Basically I have a new genome, and want to use RepeatScout to make a
library for RepeatMasker.

Here is what I do:

build_lmer_table -sequence genome.fa -freq genome.fq
RepeatScout -sequence genome.fa -output repeats.fa -freq genome.fq
filter-stage-1.prl repeats.fa &> repeats.fa.filter_1
RepeatMasker genome.fa -e abblast -lib repeats.fa.filter_1

Now:
Do I use the correct file for -lib?
RepeatMasker is still complaining about not finding Libraries/RepeatMasker.lib
and Libraries/RepeatmaskerLib.embl.

Thanks a lot in advance for any help.