Header Leaderboard Ad

Collapse

mapping 35bp solid reads with tophat unsuccessful

Collapse

Announcement

Collapse
No announcement yet.
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • mapping 35bp solid reads with tophat unsuccessful

    Hi, I recently downloaded some solid short reads (35 bp), single end, and convert them in cfasta with ahi-dump.

    I found that there are very few mappers that support solid read mapping in color space and finally i decided to use tophat using bowtie1 (which supported color space mapping).
    Unfortunately I less less than 30 % of the reads mapping.
    My previous experience has always been with 100 bp paired end reads, so I am not completely sure if I am using the right parameters for short read mapping:

    tophat -G $annotation --segment-length 17 --segment-mismatches 1 -g 1 --bowtie1 -p 12 -o $OUTPUT_FOLDER --coverage-search --color --quals $genome $READ $QUAL

    maybe is the segment-mismatch and maximum multi-hits too restrictive? (-g is 20 by default). What for your experience are the best parameters for short read mapping?

    Thanks
    Ilario

  • #2
    In general, in comparison to Illumina PE reads don't expect high mapping percentages. From memory I think 50-70% was pretty good, as the data were not extensively filtered (on the 5500xl machine at least).

    You probably don't want to use Tophat for such short reads as I don't think it will be able to find anchors/seeds successfully.

    My best experiences with SOLiD were with the commercial program NovoalignCS. You might be able to get a free trial.

    Otherwise, Shrimp2 was also not too bad.

    Why not use just bowtie1 instead of tophat2 with bowtie1 ?

    Comment


    • #3
      I did use tophat2 with bowtie1, anyway if I let the default -g option (i think it is 20) it takes ages to finish.

      As regards shrimp I didn't find any working link to download it!

      Comment


      • #4
        I recently found another non-commercial aligner for SOLiD data - it is called subread. I have only tried for Illumina data but it's very good there.

        Again, I wouldn't use tophat for such short read data.

        Comment


        • #5
          What for your experience are the best parameters for short read mapping?
          Anything that gets you quicker to re-analysing your target sample with a non-SOLiD system. You shouldn't be mapping SOLiD reads at all, especially not 35bp ones; interpreting the results is just too confusing (even for the people writing code to do the mapping).

          Comment

          Latest Articles

          Collapse

          • seqadmin
            A Brief Overview and Common Challenges in Single-cell Sequencing Analysis
            by seqadmin


            ​​​​​​The introduction of single-cell sequencing has advanced the ability to study cell-to-cell heterogeneity. Its use has improved our understanding of somatic mutations1, cell lineages2, cellular diversity and regulation3, and development in multicellular organisms4. Single-cell sequencing encompasses hundreds of techniques with different approaches to studying the genomes, transcriptomes, epigenomes, and other omics of individual cells. The analysis of single-cell sequencing data i...

            01-24-2023, 01:19 PM
          • seqadmin
            Introduction to Single-Cell Sequencing
            by seqadmin
            Single-cell sequencing is a technique used to investigate the genome, transcriptome, epigenome, and other omics of individual cells using high-throughput sequencing. This technology has provided many scientific breakthroughs and continues to be applied across many fields, including microbiology, oncology, immunology, neurobiology, precision medicine, and stem cell research.

            The advancement of single-cell sequencing began in 2009 when Tang et al. investigated the single-cell transcriptomes
            ...
            01-09-2023, 03:10 PM

          ad_right_rmr

          Collapse
          Working...
          X